arch/arm/dts/imx8mm-beacon-baseboard.dtsi

@@ -10,19 +10,19 @@
 		led0 {
 			label = "gen_led0";
 			gpios = <&pca6416_1 4 GPIO_ACTIVE_HIGH>;
-			default-state = "none";
+			default-state = "off";
 		};
 
 		led1 {
 			label = "gen_led1";
 			gpios = <&pca6416_1 5 GPIO_ACTIVE_HIGH>;
-			default-state = "none";
+			default-state = "off";
 		};
 
 		led2 {
 			label = "gen_led2";
 			gpios = <&pca6416_1 6 GPIO_ACTIVE_HIGH>;
-			default-state = "none";
+			default-state = "off";
 		};
 
 		led3 {
@@ -70,7 +70,7 @@
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_espi2>;
-	cs-gpios = <&gpio5 9 0>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
 	eeprom@0 {
@@ -210,7 +210,7 @@
 		>;
 	};
 
-	pinctrl_pcal6414: pcal6414-gpio {
+	pinctrl_pcal6414: pcal6414-gpiogrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27		0x19
 		>;
@@ -240,7 +240,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_gpio: usdhc2grpgpio {
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD2_CD_B_USDHC2_CD_B	0x41
 			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
@@ -259,7 +259,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK	0x194
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD	0x1d4
@@ -271,7 +271,7 @@
 		>;
 	};
 
-	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK	0x196
 			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD	0x1d6

arch/arm/dts/imx8mm-beacon-kit-u-boot.dtsi

@@ -37,6 +37,10 @@
 	/delete-property/ assigned-clock-rates;
 };
 
+&reg_usdhc2_vmmc {
+	u-boot,off-on-delay-us = <20000>;
+};
+
 &fec1 {
 	phy-reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
 };

arch/arm/dts/imx8mm-beacon-som.dtsi

@@ -24,6 +24,26 @@
 	cpu-supply = <&buck2_reg>;
 };
 
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-25M {
+			opp-hz = /bits/ 64 <25000000>;
+		};
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_fec1>;
@@ -52,9 +72,10 @@
 	pmic@4b {
 		compatible = "rohm,bd71847";
 		reg = <0x4b>;
+		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		rohm,reset-snvs-powered;
 
 		regulators {
@@ -116,7 +137,7 @@
 
 			ldo1_reg: LDO1 {
 				regulator-name = "ldo1";
-				regulator-min-microvolt = <3000000>;
+				regulator-min-microvolt = <1600000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
 				regulator-always-on;
@@ -124,7 +145,7 @@
 
 			ldo2_reg: LDO2 {
 				regulator-name = "ldo2";
-				regulator-min-microvolt = <900000>;
+				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <900000>;
 				regulator-boot-on;
 				regulator-always-on;
@@ -164,7 +185,7 @@
 	status = "okay";
 
 	eeprom@50 {
-		compatible = "microchip, at24c64d", "atmel,24c64";
+		compatible = "microchip,24c64", "atmel,24c64";
 		pagesize = <32>;
 		read-only;	/* Manufacturing EEPROM programmed at factory */
 		reg = <0x50>;
@@ -190,6 +211,7 @@
 		host-wakeup-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
 		device-wakeup-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
 		clocks = <&osc_32k>;
+		max-speed = <4000000>;
 		clock-names = "extclk";
 	};
 };
@@ -270,9 +292,9 @@
 			>;
 		};
 
-		pinctrl_pmic: pmicirq {
+		pinctrl_pmic: pmicirqgrp {
 			fsl,pins = <
-				MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x41
+				MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x141
 			>;
 		};
 
@@ -289,7 +311,7 @@
 			>;
 		};
 
-		pinctrl_usdhc1_gpio: usdhc1grpgpio {
+		pinctrl_usdhc1_gpio: usdhc1gpiogrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_SD1_RESET_B_GPIO2_IO10	0x41
 			>;
@@ -306,7 +328,7 @@
 			>;
 		};
 
-		pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x194
 				MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d4
@@ -317,7 +339,7 @@
 			>;
 		};
 
-		pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x196
 				MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d6
@@ -344,7 +366,7 @@
 			>;
 		};
 
-		pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+		pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x194
 				MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d4
@@ -360,7 +382,7 @@
 			>;
 		};
 
-		pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+		pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
 			fsl,pins = <
 				MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x196
 				MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d6

arch/arm/dts/imx8mm-evk-u-boot.dtsi

@@ -46,6 +46,10 @@
 	u-boot,dm-spl;
 };
 
+&reg_usdhc2_vmmc {
+	u-boot,off-on-delay-us = <20000>;
+};
+
 &pinctrl_reg_usdhc2_vmmc {
 	u-boot,dm-spl;
 };
@@ -96,10 +100,14 @@
 
 &usdhc2 {
 	u-boot,dm-spl;
+	sd-uhs-sdr104;
+	sd-uhs-ddr50;
 };
 
 &usdhc3 {
 	u-boot,dm-spl;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
 };
 
 &i2c1 {

arch/arm/dts/imx8mm-verdin-u-boot.dtsi

@@ -2,7 +2,6 @@
 /*
  * Copyright 2020 Toradex
  */
-
 / {
 	wdt-reboot {
 		compatible = "wdt-reboot";
@@ -90,11 +89,11 @@
 	u-boot,dm-spl;
 };
 
-&{/soc@0/bus@30800000/i2c@30a20000/pmic@4b} {
+&{/soc@0/bus@30800000/i2c@30a20000/pmic} {
 	u-boot,dm-spl;
 };
 
-&{/soc@0/bus@30800000/i2c@30a20000/pmic@4b/regulators} {
+&{/soc@0/bus@30800000/i2c@30a20000/pmic/regulators} {
 	u-boot,dm-spl;
 };
 

arch/arm/dts/imx8mm-verdin.dts

@@ -203,115 +203,123 @@
 	pinctrl-0 = <&pinctrl_i2c1>;
 	status = "okay";
 
-	pmic@4b {
-		compatible = "rohm,bd71840", "rohm,bd71837";
-		bd71837,pmic-buck2-uses-i2c-dvs;
-		bd71837,pmic-buck2-dvs-voltage = <1000000>, <900000>, <0>; /* VDD_ARM: Run-Idle */
-		gpio_intr = <&gpio1 3 GPIO_ACTIVE_LOW>;
-		/* PMIC BD71837 PMIC_nINT GPIO1_IO3 */
+	/* Assembled on V1.1 HW and later */
+	pmic {
+		reg = <0x25>;
+		u-boot,dm-spl;
+		compatible = "nxp,pca9450a";
+		/* PMIC PCA9450 PMIC_nINT GPIO1_IO3 */
 		pinctrl-0 = <&pinctrl_pmic>;
-		reg = <0x4b>;
-
-		gpo {
-			rohm,drv = <0x0C>;	/* 0b0000_1100 all gpos with cmos output mode */
-		};
+		gpio_intr = <&gpio1 3 GPIO_ACTIVE_LOW>;
 
 		regulators {
-			buck1_reg: BUCK1 {
-				regulator-always-on;
-				regulator-boot-on;
+			u-boot,dm-spl;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pca9450,pmic-buck2-uses-i2c-dvs;
+			/* Run/Standby voltage */
+			pca9450,pmic-buck2-dvs-voltage = <950000>, <850000>;
+
+			buck1_reg: regulator@0 {
+				reg = <0>;
 				regulator-compatible = "buck1";
-				regulator-max-microvolt = <1300000>;
-				regulator-min-microvolt = <700000>;
-				regulator-ramp-delay = <1250>;
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <2187500>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
 			};
 
-			buck2_reg: BUCK2 {
-				regulator-always-on;
-				regulator-boot-on;
+			buck2_reg: regulator@1 {
+				reg = <1>;
 				regulator-compatible = "buck2";
-				regulator-max-microvolt = <1300000>;
-				regulator-min-microvolt = <700000>;
-				regulator-ramp-delay = <1250>;
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <2187500>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
 			};
 
-			buck5_reg: BUCK5 {
-				regulator-always-on;
+			buck3_reg: regulator@2 {
+				reg = <2>;
+				regulator-compatible = "buck3";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <2187500>;
 				regulator-boot-on;
-				regulator-compatible = "buck5";
-				regulator-max-microvolt = <1350000>;
-				regulator-min-microvolt = <700000>;
+				regulator-always-on;
 			};
 
-			buck6_reg: BUCK6 {
-				regulator-always-on;
+			buck4_reg: regulator@3 {
+				reg = <3>;
+				regulator-compatible = "buck4";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3400000>;
 				regulator-boot-on;
-				regulator-compatible = "buck6";
-				regulator-max-microvolt = <3300000>;
-				regulator-min-microvolt = <3000000>;
+				regulator-always-on;
 			};
 
-			buck7_reg: BUCK7 {
-				regulator-always-on;
+			buck5_reg: regulator@4 {
+				reg = <4>;
+				regulator-compatible = "buck5";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3400000>;
 				regulator-boot-on;
-				regulator-compatible = "buck7";
-				regulator-max-microvolt = <1995000>;
-				regulator-min-microvolt = <1605000>;
+				regulator-always-on;
 			};
 
-			buck8_reg: BUCK8 {
-				regulator-always-on;
+			buck6_reg: regulator@5 {
+				reg = <5>;
+				regulator-compatible = "buck6";
+				regulator-min-microvolt = <600000>;
+				regulator-max-microvolt = <3400000>;
 				regulator-boot-on;
-				regulator-compatible = "buck8";
-				regulator-max-microvolt = <1400000>;
-				regulator-min-microvolt = <800000>;
+				regulator-always-on;
 			};
 
-			ldo1_reg: LDO1 {
-				regulator-always-on;
-				regulator-boot-on;
+			ldo1_reg: regulator@6 {
+				reg = <6>;
 				regulator-compatible = "ldo1";
+				regulator-min-microvolt = <1600000>;
 				regulator-max-microvolt = <3300000>;
-				regulator-min-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
 			};
 
-			ldo2_reg: LDO2 {
-				regulator-always-on;
-				regulator-boot-on;
+			ldo2_reg: regulator@7 {
+				reg = <7>;
 				regulator-compatible = "ldo2";
-				regulator-max-microvolt = <900000>;
-				regulator-min-microvolt = <900000>;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1150000>;
+				regulator-boot-on;
+				regulator-always-on;
 			};
 
-			ldo3_reg: LDO3 {
-				regulator-always-on;
-				regulator-boot-on;
+			ldo3_reg: regulator@8 {
+				reg = <8>;
 				regulator-compatible = "ldo3";
+				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <3300000>;
-				regulator-min-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
 			};
 
-			ldo4_reg: LDO4 {
-				regulator-always-on;
-				regulator-boot-on;
+			ldo4_reg: regulator@9 {
+				reg = <9>;
 				regulator-compatible = "ldo4";
-				regulator-max-microvolt = <1800000>;
-				regulator-min-microvolt = <900000>;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
 			};
 
-			ldo5_reg: LDO5 {
+			ldo5_reg: regulator@10 {
+				reg = <10>;
 				regulator-compatible = "ldo5";
+				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <3300000>;
-				regulator-min-microvolt = <3300000>;
 			};
 
-			ldo6_reg: LDO6 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-compatible = "ldo6";
-				regulator-max-microvolt = <1800000>;
-				regulator-min-microvolt = <900000>;
-			};
 		};
 	};
 
@@ -321,12 +329,6 @@
 		reg = <0x32>;
 	};
 
-	adc@34 {
-		compatible = "maxim,max11607";
-		reg = <0x34>;
-		vcc-supply = <&ldo5_reg>;
-	};
-
 	eeprom_module: eeprom@50 {
 		compatible = "st,24c02", "atmel,24c02", "i2c-eeprom";
 		pagesize = <16>;

arch/arm/dts/imx8mm.dtsi

@@ -18,10 +18,18 @@
 
 	aliases {
 		ethernet0 = &fec1;
+		gpio0 = &gpio1;
+		gpio1 = &gpio2;
+		gpio2 = &gpio3;
+		gpio3 = &gpio4;
+		gpio4 = &gpio5;
 		i2c0 = &i2c1;
 		i2c1 = &i2c2;
 		i2c2 = &i2c3;
 		i2c3 = &i2c4;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+		mmc2 = &usdhc3;
 		serial0 = &uart1;
 		serial1 = &uart2;
 		serial2 = &uart3;
@@ -29,14 +37,6 @@
 		spi0 = &ecspi1;
 		spi1 = &ecspi2;
 		spi2 = &ecspi3;
-		mmc0 = &usdhc1;
-		mmc1 = &usdhc2;
-		mmc2 = &usdhc3;
-		gpio0 = &gpio1;
-		gpio1 = &gpio2;
-		gpio2 = &gpio3;
-		gpio3 = &gpio4;
-		gpio4 = &gpio5;
 	};
 
 	cpus {
@@ -68,6 +68,7 @@
 			nvmem-cells = <&cpu_speed_grade>;
 			nvmem-cell-names = "speed_grade";
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_1: cpu@1 {
@@ -80,6 +81,7 @@
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_2: cpu@2 {
@@ -92,6 +94,7 @@
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_3: cpu@3 {
@@ -104,6 +107,7 @@
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
+			#cooling-cells = <2>;
 		};
 
 		A53_L2: l2-cache0 {
@@ -125,7 +129,7 @@
 
 		opp-1600000000 {
 			opp-hz = /bits/ 64 <1600000000>;
-			opp-microvolt = <900000>;
+			opp-microvolt = <950000>;
 			opp-supported-hw = <0xc>, <0x7>;
 			clock-latency-ns = <150000>;
 			opp-suspend;
@@ -204,6 +208,38 @@
 		arm,no-tick-in-suspend;
 	};
 
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <2000>;
+			thermal-sensors = <&tmu>;
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <85000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit0: trip1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device =
+						<&A53_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+						<&A53_3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
 	usbphynop1: usbphynop1 {
 		compatible = "usb-nop-xceiv";
 		clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
@@ -227,12 +263,14 @@
 		ranges = <0x0 0x0 0x0 0x3e000000>;
 
 		aips1: bus@30000000 {
-			compatible = "simple-bus";
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x30000000 0x400000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x30000000 0x30000000 0x400000>;
 
 			sai1: sai@30010000 {
+				#sound-dai-cells = <0>;
 				compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
 				reg = <0x30010000 0x10000>;
 				interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
@@ -246,6 +284,7 @@
 			};
 
 			sai2: sai@30020000 {
+				#sound-dai-cells = <0>;
 				compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
 				reg = <0x30020000 0x10000>;
 				interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
@@ -273,6 +312,7 @@
 			};
 
 			sai5: sai@30050000 {
+				#sound-dai-cells = <0>;
 				compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
 				reg = <0x30050000 0x10000>;
 				interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
@@ -286,6 +326,7 @@
 			};
 
 			sai6: sai@30060000 {
+				#sound-dai-cells = <0>;
 				compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
 				reg = <0x30060000 0x10000>;
 				interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
@@ -363,6 +404,13 @@
 				gpio-ranges = <&iomuxc 0 119 30>;
 			};
 
+			tmu: tmu@30260000 {
+				compatible = "fsl,imx8mm-tmu";
+				reg = <0x30260000 0x10000>;
+				clocks = <&clk IMX8MM_CLK_TMU_ROOT>;
+				#thermal-sensor-cells = <0>;
+			};
+
 			wdog1: watchdog@30280000 {
 				compatible = "fsl,imx8mm-wdt", "fsl,imx21-wdt";
 				reg = <0x30280000 0x10000>;
@@ -419,7 +467,7 @@
 				reg = <0x30340000 0x10000>;
 			};
 
-			ocotp: ocotp-ctrl@30350000 {
+			ocotp: efuse@30350000 {
 				compatible = "fsl,imx8mm-ocotp", "syscon";
 				reg = <0x30350000 0x10000>;
 				clocks = <&clk IMX8MM_CLK_OCOTP_ROOT>;
@@ -455,6 +503,8 @@
 					compatible = "fsl,sec-v4.0-pwrkey";
 					regmap = <&snvs>;
 					interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&clk IMX8MM_CLK_SNVS_ROOT>;
+					clock-names = "snvs-pwrkey";
 					linux,keycode = <KEY_POWER>;
 					wakeup-source;
 					status = "disabled";
@@ -469,16 +519,20 @@
 					 <&clk_ext3>, <&clk_ext4>;
 				clock-names = "osc_32k", "osc_24m", "clk_ext1", "clk_ext2",
 					      "clk_ext3", "clk_ext4";
-				assigned-clocks = <&clk IMX8MM_CLK_NOC>,
+				assigned-clocks = <&clk IMX8MM_CLK_A53_SRC>,
+						<&clk IMX8MM_CLK_A53_CORE>,
+						<&clk IMX8MM_CLK_NOC>,
 						<&clk IMX8MM_CLK_AUDIO_AHB>,
 						<&clk IMX8MM_CLK_IPG_AUDIO_ROOT>,
 						<&clk IMX8MM_SYS_PLL3>,
 						<&clk IMX8MM_VIDEO_PLL1>,
 						<&clk IMX8MM_AUDIO_PLL1>,
 						<&clk IMX8MM_AUDIO_PLL2>;
-				assigned-clock-parents = <&clk IMX8MM_SYS_PLL3_OUT>,
+				assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_800M>,
+							 <&clk IMX8MM_ARM_PLL_OUT>,
+							 <&clk IMX8MM_SYS_PLL3_OUT>,
 							 <&clk IMX8MM_SYS_PLL1_800M>;
-				assigned-clock-rates = <0>,
+				assigned-clock-rates = <0>, <0>, <0>,
 							<400000000>,
 							<400000000>,
 							<750000000>,
@@ -496,7 +550,8 @@
 		};
 
 		aips2: bus@30400000 {
-			compatible = "simple-bus";
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x30400000 0x400000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x30400000 0x30400000 0x400000>;
@@ -555,10 +610,12 @@
 		};
 
 		aips3: bus@30800000 {
-			compatible = "simple-bus";
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x30800000 0x400000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges = <0x30800000 0x30800000 0x400000>;
+			ranges = <0x30800000 0x30800000 0x400000>,
+				 <0x8000000 0x8000000 0x10000000>;
 
 			ecspi1: spi@30820000 {
 				compatible = "fsl,imx8mm-ecspi", "fsl,imx51-ecspi";
@@ -718,6 +775,14 @@
 				status = "disabled";
 			};
 
+			mu: mailbox@30aa0000 {
+				compatible = "fsl,imx8mm-mu", "fsl,imx6sx-mu";
+				reg = <0x30aa0000 0x10000>;
+				interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_MU_ROOT>;
+				#mbox-cells = <2>;
+			};
+
 			usdhc1: mmc@30b40000 {
 				compatible = "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
 				reg = <0x30b40000 0x10000>;
@@ -760,6 +825,19 @@
 				status = "disabled";
 			};
 
+			flexspi: spi@30bb0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "nxp,imx8mm-fspi";
+				reg = <0x30bb0000 0x10000>, <0x8000000 0x10000000>;
+				reg-names = "fspi_base", "fspi_mmap";
+				interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_QSPI_ROOT>,
+					 <&clk IMX8MM_CLK_QSPI_ROOT>;
+				clock-names = "fspi", "fspi_en";
+				status = "disabled";
+			};
+
 			sdma1: dma-controller@30bd0000 {
 				compatible = "fsl,imx8mm-sdma", "fsl,imx8mq-sdma";
 				reg = <0x30bd0000 0x10000>;
@@ -776,7 +854,8 @@
 				reg = <0x30be0000 0x10000>;
 				interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+					     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clk IMX8MM_CLK_ENET1_ROOT>,
 					 <&clk IMX8MM_CLK_ENET1_ROOT>,
 					 <&clk IMX8MM_CLK_ENET_TIMER>,
@@ -800,7 +879,8 @@
 		};
 
 		aips4: bus@32c00000 {
-			compatible = "simple-bus";
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x32c00000 0x400000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x32c00000 0x32c00000 0x400000>;
@@ -896,7 +976,6 @@
 		ddr-pmu@3d800000 {
 			compatible = "fsl,imx8mm-ddr-pmu", "fsl,imx8m-ddr-pmu";
 			reg = <0x3d800000 0x400000>;
-			interrupt-parent = <&gic>;
 			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
 		};
 	};

arch/arm/dts/imx8mn-ddr4-evk-u-boot.dtsi

@@ -47,6 +47,10 @@
 	u-boot,dm-spl;
 };
 
+&reg_usdhc2_vmmc {
+	u-boot,off-on-delay-us = <20000>;
+};
+
 &pinctrl_uart2 {
 	u-boot,dm-spl;
 };
@@ -93,10 +97,14 @@
 
 &usdhc2 {
 	u-boot,dm-spl;
+	sd-uhs-sdr104;
+	sd-uhs-ddr50;
 };
 
 &usdhc3 {
 	u-boot,dm-spl;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
 };
 
 &wdog1 {

arch/arm/dts/imx8mp-evk-u-boot.dtsi

@@ -48,6 +48,10 @@
 	u-boot,dm-spl;
 };
 
+&reg_usdhc2_vmmc {
+	u-boot,off-on-delay-us = <20000>;
+};
+
 &reg_usdhc2_vmmc {
 	u-boot,dm-spl;
 };
@@ -122,10 +126,14 @@
 
 &usdhc2 {
 	u-boot,dm-spl;
+	sd-uhs-sdr104;
+	sd-uhs-ddr50;
 };
 
 &usdhc3 {
 	u-boot,dm-spl;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
 };
 
 &wdog1 {

arch/arm/dts/imx8mq-evk-u-boot.dtsi

+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+&reg_usdhc2_vmmc {
+	u-boot,off-on-delay-us = <20000>;
+};
+
+&usdhc1 {
+	mmc-hs400-1_8v;
+};
+
+&usdhc2 {
+	sd-uhs-sdr104;
+	sd-uhs-ddr50;
+};

arch/arm/dts/imx8mq-phanbell-u-boot.dtsi

+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+&reg_usdhc2_vmmc {
+	u-boot,off-on-delay-us = <20000>;
+};

arch/arm/dts/imx8qm-rom7720-a1.dts

@@ -293,7 +293,7 @@
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_fec1>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy0>;
 	fsl,ar8031-phy-fixup;
 	fsl,magic-packet;
@@ -318,7 +318,7 @@
 &fec2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_fec2>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy1>;
 	fsl,ar8031-phy-fixup;
 	fsl,magic-packet;

arch/arm/dts/meson-g12b-a311d-khadas-vim3-u-boot.dtsi

@@ -4,4 +4,5 @@
  * Author: Neil Armstrong <narmstrong@baylibre.com>
  */
 
+#include "meson-g12-common-u-boot.dtsi"
 #include "meson-khadas-vim3-u-boot.dtsi"

arch/arm/dts/meson-khadas-vim3-u-boot.dtsi

@@ -4,8 +4,6 @@
  * Author: Neil Armstrong <narmstrong@baylibre.com>
  */
 
-#include "meson-g12-common-u-boot.dtsi"
-
 / {
 	aliases {
 		spi0 = &spifc;

arch/arm/dts/meson-sm1-khadas-vim3l-u-boot.dtsi

@@ -4,4 +4,5 @@
  * Author: Neil Armstrong <narmstrong@baylibre.com>
  */
 
+#include "meson-sm1-u-boot.dtsi"
 #include "meson-khadas-vim3-u-boot.dtsi"

arch/arm/dts/meson-sm1-odroid-c4-u-boot.dtsi

@@ -4,10 +4,14 @@
  * Author: Neil Armstrong <narmstrong@baylibre.com>
  */
 
-#include "meson-g12-common-u-boot.dtsi"
+#include "meson-sm1-u-boot.dtsi"
 
 &ethmac {
 	snps,reset-gpio = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
 	snps,reset-delays-us = <0 10000 1000000>;
 	snps,reset-active-low;
 };
+
+&tflash_vdd {
+	gpio = <&gpio_ao GPIOAO_3 GPIO_OPEN_DRAIN>;
+};

arch/arm/dts/meson-sm1-sei610-u-boot.dtsi

@@ -4,4 +4,4 @@
  * Author: Neil Armstrong <narmstrong@baylibre.com>
  */
 
-#include "meson-g12-common-u-boot.dtsi"
+#include "meson-sm1-u-boot.dtsi"

arch/arm/dts/meson-sm1-u-boot.dtsi

+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12-common-u-boot.dtsi"
+
+&sd_emmc_a {
+	compatible = "amlogic,meson-sm1-mmc";
+};
+
+&sd_emmc_b {
+	compatible = "amlogic,meson-sm1-mmc";
+};
+
+&sd_emmc_c {
+	compatible = "amlogic,meson-sm1-mmc";
+};
+

arch/arm/dts/rk3399-pinebook-pro-u-boot.dtsi

@@ -7,10 +7,6 @@
 #include "rk3399-sdram-lpddr4-100.dtsi"
 
 / {
-	aliases {
-		spi0 = &spi1;
-	};
-
 	chosen {
 		u-boot,spl-boot-order = "same-as-spl", &sdhci, &spiflash, &sdmmc;
 	};

arch/arm/dts/rk3399-rockpro64-u-boot.dtsi

@@ -6,10 +6,6 @@
 #include "rk3399-u-boot.dtsi"
 #include "rk3399-sdram-lpddr4-100.dtsi"
 / {
-	aliases {
-		spi0 = &spi1;
-	};
-
 	chosen {
 		u-boot,spl-boot-order = "same-as-spl", &spi_flash, &sdmmc, &sdhci;
 	};